Philips Indoor Furnishings Series 1 1 User Manual

Lighting Systems A-5  
1BHFꢃꢂꢃPGꢃꢆꢃ  
"MFSPOÜꢃ4FSJFTꢃꢂꢃꢌꢃꢂꢌ-JHIUꢃ5ꢈꢃ1FSꢃꢍhꢃ ꢂꢆꢂꢎꢋꢆDNꢊꢃ4FDUJPO  
7
2
4
1
3
9-9/16”  
(24.29cm)  
6
3-5/8” (9.21cm)  
12-3/8” (31.43cm)  
NOT TO SCALE  
Module Ordering Information  
Family  
Series  
Track  
Length  
Shielding  
Lamps  
Finish  
Options  
A
1
A
C
E1 = Emergency Pack, 120v  
E2 = Emergency Pack, 277v  
D1 = Dimming 120v  
D2 = Dimming 277v  
X5 = 5 Through Wires  
A = No Shield  
B = Solid Shield  
C = Perf Shield  
D = Lens Shield  
28 = 28w  
54 = 54w  
4 = 4-Foot  
8 = 8-Foot  
12 = 12-Foot  
WH = White  
AL = Aluminum  
A = Track  
B = No Track  
Complete ordering instructions below.  
Features  
Electrical  
1. Housing: Extruded aluminum housing in lengths of 4’ (121.92cm), 8’ (243.84cm)  
and 12’ (365.76cm). There are no exposed fasteners. The end caps are die-cast  
aluminum sculpted and finished to match the housing.  
Ballast is <10% THD, 1.0 ballast factor, program start. Color-coded quick  
connectors allow ease of connection for joiner modules. For special circuiting  
consult factory. Factory installed ballast disconnect allows the ballast to be  
disconnected from and reconnected to incoming power under load without turning  
the entire circtuit off.  
2. Lens: Extruded clear acrylic linear prismatic lens.  
3. Reflector: Die-formed high purity anodized specular aluminum.  
4. Lamping: One T5 28W or 54W lamp per four-foot nominal length. Provided  
by others.  
5. Alignment Mechanism: The housing and the end cap each have a draw tight  
mechanism that creates a hairline joint along and at the ends of the run. To  
operate the mechanism, the installer tightens two screws.  
6. Track Option: The housing has the capability of having single circuit Lytespan  
track fixtures for accent lighting. The track is an integral component of the  
housing. The fixture housing comes with a cover to conceal any portion of the  
track that doesn’t have a track fixture installed. The cover can be cut to length  
in the field. There is an optional cover (ATC) that creates a nearly seamless  
transition from the fluorescent fixture to the track fixture.  
Dimming: 120/277 VAC 1% dimming level, 4 or 5 wire feed required.  
Emergency Battery Pack: 28 watt: 520 lumens @ 90 minutes, 54 watt: 700  
lumens @ 90 minutes.  
There are two types of power feed end sets for the track option. One has a stem  
containing five solid wires and the other end set has one 5 wire and one 3 wire  
stem. Single power feed end sets allow for 16 amps of track fixtures per run while  
dual power feed end sets allow 32 amps per run.  
®
Ordering Instructions  
Individual Fixtures:  
1. Order number of MODULES required.  
2. Order one POWER FEED END SET per MODULE.  
7. Shielding: Die-formed 18 gauge perforated steel. Pattern has 0.117” (0.30cm)  
holes on 5/32” (0.40cm) centers and is 51% open. High reflectance white finish.  
Continuous Rows:  
1. Determine run length.  
Labels  
2. Order the appropriate number of MODULES for the complete run.  
3. Order one POWER FEED END SET per run.  
4. Order one INTERMEDIATE SUSPENSION per MODULE minus one per run.  
5. For runs that exceed amperage limits, order the appropriate number of  
INTERMEDIATE POWER FEEDS.  
UL, cUL and I.B.E.W.  
Finish  
Powder coated baked white or silver enamel.  
Custom colors available, consult factory.  
Mountings  
Job Information  
Type:  
All mounting is on 48” (121.92cm), 96” (243.84cm) and 144” (365.76cm) centers.  
Cable Suspension (not shown) 4-1/2" (11.43cm) diameter flat canopy finished  
white enamel, 1/16" (0.16cm) diameter stainless steel aircraft cable adjustable up  
to 36" (91.44cm) and adjustable cable gripper. Cable mounting at the ends of a run  
is not available when track is being used. Installing stems at the ends of the run  
will prevent the fixture from hanging off center caused by the weight of the track  
fixture. Cable suspension can be used in the center of runs that have track  
installed. Consult factory for other options.  
Job Name:  
Cat. No.:  
Lamp(s):  
Notes:  
Stem Mounting (not shown) - 4-1/2" (11.43cm) diameter flat canopy, 1/4"  
(0.64cm) IP (1/2” (1.27cm) OD) stem. The stem can accommodate up to 2-12 gauge  
and 3-18 gauge solid wires. All components have a white finish.  
ꢀꢁꢂꢃ"JSQPSUꢃ3PBEꢄꢃ'BMMꢃ3JWFSꢄꢃ."ꢃꢅꢆꢇꢆꢅꢃtꢃ ꢈꢅꢉꢊꢃꢀꢇꢋꢌꢉꢂꢁꢂꢃtꢃ'BYꢃ ꢈꢅꢉꢊꢃꢀꢇꢍꢌꢍꢇꢂꢅ  
We reserve the right to change details of design, materials and finish.  
XXXꢎMJHIUPMJFSꢎDPNꢃ½ꢃꢆꢅꢅꢉꢃ1IJMJQTꢃ(SPVQꢃt $ꢅꢋꢅꢉ  
 

Peavey Stereo Amplifier 26 C User Manual
Pelco Camera Lens 12ZM85X6C CE User Manual
Pelco Satellite Radio FR85081 User Manual
Pelco Security Camera AND TVJ6MS 1 User Manual
Pella Window 80WW0101 User Manual
Philips Electric Toothbrush HX3551 User Manual
Philips Universal Remote SBCRU885 User Manual
Pioneer Musical Toy Instrument RMX 500 User Manual
Pioneer Speaker S DV990ST User Manual
Poulan Snow Blower PP1130ESB User Manual