Precor Fitness Equipment S315 User Manual

S3.15  
Multi-Hip Option  
Assembly Instructions  
 
S3.15 Multi-Hip Option Assembly Instructions  
Table of Contents  
Important Safety Instructions....................................................................... 2  
Personal Safety During Assembly ........................................................................................... 2  
Obtaining Service .................................................................................................................... 2  
BeforeYou Begin ........................................................................................... 4  
Unpacking the Equipment ....................................................................................................... 4  
1
2
Preparations................................................................................................... 5  
Required Tools......................................................................................................................... 5  
Installation Requirements ........................................................................................................ 5  
Assembly Tips ......................................................................................................................... 5  
Assembly Instructions .................................................................................. 6  
1. Attach the Multi-Hip to the S3.15 .................................................................................. 7  
2. Assemble the Multi-Hip ................................................................................................. 8  
3. Install the Multi-Hip Cable ............................................................................................. 9  
4. Attach the Multi-Hip Cable to the S3.15 ........................................................................ 10  
3
4
Warranty ......................................................................................................... 11  
Limited Warranty Statement .................................................................................................... 11  
Warranty Registration Card ..................................................................................................... 13  
Specifications ............................................................................................................. Back cover  
Table of Contents  
page 3  
 
S3.15 Multi-Hip Option Assembly Instructions  
1
Before You Begin  
Thank you for purchasing the Multi-Hip Option. This  
option will add a new dimension to your strength-  
training regimen. For proper installation, please read  
this guide thoroughly and follow the assembly  
instructions.  
S3.15  
Unpacking the Equipment  
The Multi-Hip Option is carefully tested and inspected  
before shipment. Precor Strength ships the unit in  
several pieces that require assembly. Ask for  
assistance during the assembly process.  
Multi-Hip Option  
Review the Installation Requirements.  
Carefully unpack the pieces and lay them on the  
floor near the location where you plan to use the  
equipment.  
If any items are missing, contact the dealer from whom  
you purchased the unit. For more information, refer to  
Obtaining Service.  
Before You Begin  
page 4  
 
S3.15 Multi-Hip Option Assembly Instructions  
Installation Requirements  
Most fasteners are ³⁄₈ inch unless otherwise noted.  
To find out the length of a particular fastener,  
measure its shank (the long, narrow part beneath  
the head). Refer to the following diagram:  
Follow these installation requirements when  
assembling the unit:  
Fill out and mail the warranty registration card.  
Set up the Multi-Hip Option on a solid, flat surface.  
A smooth, flat surface under the unit helps keep  
it level.  
Fastener head  
2
Preparations  
You must review and follow the instructions in this  
guide. If you do not assemble and use the Multi-Hip  
Option according to the following guidelines, you could  
void the Precor Limited Warranty.  
Provide ample space around the machine.  
Open space around the machine allows for easier  
access.  
To determine the  
length of a fastener,  
measure its shank.  
Fastener threads  
Shank  
Insert all fasteners in the same direction. For  
aesthetic purposes, insert all the fasteners in the  
same direction unless specified (in text or  
illustrations) to do otherwise.  
Required Tools  
Tools that you need to obtain before assembling the  
unit include:  
Zinc fasteners are used with the titanium parts.  
Black fasteners are used when assembling the  
stone gray painted surfaces.  
Leave room for adjustments. Tighten fasteners  
(such as screws, nuts, and bolts), so the unit is  
stable, but leaves room for adjustments. Do not  
fully tighten fasteners until instructed (in the steps)  
to do so.  
⁹⁄₁₆-inch socket  
³⁄₄-inch socket  
Most fasteners are fitted to the frame or pulley, you  
will need to disassemble the fasteners before  
proceeding with each step. Some pieces have  
extra holes that you will not use. Use only those  
holes indicated in the instructions and illustrations.  
⁹⁄₁₆-inch box-end wrench  
³⁄₄-inch box-end wrench  
Crescent wrench  
Assembly Tips  
Fasteners may become loose and fall off during  
Wire tie cutter (cuts plastic tie wraps)  
Utility knife  
Read all caution notes on each page before  
completing that step.  
shipment. Inspect the plastic wrap and packaging  
for loose parts. To alleviate confusion during  
assembly, reattach the loose fasteners and pulleys  
found in the packaging.  
While you may be able to assemble the Multi-Hip  
Option by reading the illustrations only, refer to the  
text for important safety cautions and notes.  
A black 6-inch scale with white numbers is  
provided at the bottom of every assembly  
instruction page. Use this scale to identify the  
correct fastener size. The head of a fastener is not  
used in measuring the length.  
Preparations  
page 5  
 
S3.15 Multi-Hip Option Assembly Instructions  
Assembly  
Instructions  
3
Assembly of the Multi-Hip Option takes professional  
installers about ¹⁄₂ hour to complete. If this is the first  
time you have assembled this type of equipment, plan  
on significantly more time.  
Selector Hub  
Professional installers are highly recommended!  
However, if you acquire the appropriate tools, obtain  
assistance, and follow the assembly steps sequentially,  
the process will take time, but is fairly easy.  
Roller pad  
CAUTION: Obtain assistance! Do not attempt to  
assemble the Multi-Hip Option by yourself. Review  
the Installation Requirements before proceeding  
with the following steps.  
With so many assembled parts, proper alignment and  
adjustment is critical. While tightening the fasteners, be  
sure to leave room for adjustments. Do not fully tighten  
fasteners until instructed to do so.  
Important: Be careful to assemble components in the  
sequence presented in this manual.  
Crossbrace  
1
2
3
4
5
6
Assembly Instructions  
page 6  
 
S3.15 Multi-Hip Option Assembly Instructions  
1. Attach the Multi-Hip to  
the S3.15  
Important: Most fasteners are fitted to the frame  
or pulley, you will need to disassemble the  
fasteners before proceeding with each step.  
2 - 2¹⁄₄" bolts  
A. Attach the Multi-Hip Base to the S3.15 Rear  
Crossbar using  
2 - washers  
B
three 1¼-inch hex head bolts  
three flat washers  
three spring washers  
three locknuts  
B. Position the Crossbrace against the S3.15 Main  
Base and place it on top of the Multi-Hip flange.  
Attach the Crossbrace to the Multi-Hip using  
two 2¹⁄₄-inch hex head bolts  
two flat washers  
Crossbrace  
Multi-Hip Flange  
C. Attach the Crossbrace to the S3.15 Main Base  
Rear  
Crossbar  
using  
two 4¹⁄₄-inch hex head bolts  
four radius washers  
two locknuts  
Multi-Hip  
Upright  
Note: If you plan to install the S3.15 Leg Press  
Option immediately after you complete the Multi-  
Hip Option assembly, place two washers and two  
locknuts on the fastener ends finger tight so they  
provide stability, but can easily be removed.  
Spring  
Washer  
3 - 1¼" bolts  
3 - flat washers  
3 - spring washers  
3 - locknuts  
Main Base  
A
2 - 4¹⁄₄" bolts  
4 - radius washers  
2 - locknuts  
C
1
2
3
4
5
6
Step 1. Attach the Multi-Hip to the S3.15  
page 7  
 
S3.15 Multi-Hip Option Assembly Instructions  
2. Assemble the Multi-Hip  
Important: The orientation of the Handlebar fasteners,  
the Roller Arm, and the Selector Stem is critical for the  
proper alignment of the Selector Hub. Assemble the  
parts with the orientation shown in the illustration.  
Selector Hub  
2 - 2½" bolts  
4 - washers  
2 - locknuts  
A
C
Selector Stem  
Roller Arm  
A. Attach the Handlebar to the Multi-Hip using  
two 2½-inch hex head bolts  
four flat washers  
1 - ³⁄₄" zinc  
buttonhead bolt  
1 - washer  
two locknuts.  
Roller Pad  
B. Attach the Roller Arm to the Selector Stem using  
one ³⁄₄-inch zinc buttonhead bolt  
one zinc washer  
C. Install the Selector Hub assembly to the Multi-Hip  
Upright using  
1 - ³⁄₄" zinc  
buttonhead bolt  
1 - washer  
B
one ³⁄₄-inch zinc buttonhead bolt  
one zinc washer  
Multi-Hip  
Upright  
D. Wrench tighten all fasteners.  
1
2
3
4
5
6
Step 2. Assemble the Multi-Hip  
page 8  
 
S3.15 Multi-Hip Option Assembly Instructions  
3. Install the Multi-Hip Cable  
Pulley assemblies  
A. Feed the tab end of the Multi-Hip Cable 130194  
3½-inch Pulley (used on gray  
painted parts)  
between the two 3½-inch pulleys on the Multi-Hip  
Upright and attach the cable to the Selector Hub  
using  
one shaft  
two e-clips  
1 - bolt  
2 - shoulder spacers  
1 - locknut  
Selector Hub  
B. Remove the lower 3¹⁄₂-inch pulley on the Multi-Hip  
Upright. Feed the cable around it and reattach it  
using  
1 - shaft  
2 - e-clips  
A
3½-inch Pulley (used on  
titanium parts)  
one 4-inch hex head bolt  
two shoulder spacers  
one locknut  
1 - zinc bolt  
2 - zinc washers  
1 - zinc locknut  
C. Remove the 3¹⁄₂-inch pulley from its pulley bracket.  
Feed the cable around it and reattach it using  
one 2¼-inch hex head bolt  
Multi-Hip  
Upright  
two flat washers  
one locknut  
D. Wrench tighten all pulley fasteners.  
1 - 2¼" bolt  
2 - washers  
1 - locknut  
C
1 - 4" bolt  
2 - 1" shoulder spacers  
1 - locknut  
B
1
2
3
4
5
6
Step 3. Install the Multi-Hip Cable  
page 9  
 
S3.15 Multi-Hip Option Assembly Instructions  
4. Attach the Multi-Hip Cable to  
the S3.15  
A. Attach the end of the Multi-Hip Cable to the S3.15  
Cable using  
one 1-inch hex head bolt  
one locknut  
B. Wrench tighten the locknut, but do not bend the  
flanges.  
C. Position the Pivoting Bracket to align the cables.  
If necessary, loosen the fastener securing the  
Pivoting Bracket to the Main Base. Retighten the  
fastener after aligning the cables.  
This completes the assembly of the Multi-Hip Option.  
Before using the Multi-Hip, check the cable tension  
throughout the S3.15 unit. Refer to Cable Adjustments  
and Maintenance in the S3.15 Assembly and  
Maintenance Guide.  
C
1 - 1" bolt  
1 - locknut  
A
B
1
2
3
4
5
6
Step 4. Attach the Multi-Hip Cable to the S3.15  
page 10  
 
Precor Residential Equipment Limited Warranty  
PLEASE READ THESE WARRANTY TERMS AND CONDITIONS CAREFULLY BEFORE USING  
YOUR PRECOR INCORPORATED PRODUCT. BY USING THE EQUIPMENT, YOU ARE  
CONSENTING TO BE BOUND BY THE FOLLOWING WARRANTY TERMS AND CONDITIONS.  
3. Warranty of all Precor products applies to residential use only and is void when products are  
used in a nonresidential environment or installed in a country other than where sold.  
4. Except in Canada, Precor does not pay labor outside the United States.  
5. Warranties outside the United States and Canada may vary. Please contact your local Dealer  
for details.  
Limited Warranty.  
Precor Incorporated warrants all new Precor products to be free from defects in materials and  
manufacture for the warranty period set forth below. The warranty period commences on the  
invoice date of original purchase. This warranty applies only against defects discovered within  
the warranty period and extends only to the original purchaser of the product. Parts repaired or  
replaced under the terms of this warranty will be warranted for the remainder of the original  
warranty period only. To make claim under warranty, the buyer must notify Precor or their  
authorized Precor dealer within 30 days after the date of discovery of any nonconformity and  
make the affected product available for inspection by Precor or its service representative.  
Precor’s obligations under this warranty are limited and set forth below.  
This limited warranty shall not apply to:  
1. Software version upgrades  
2. Cosmetic items, including, but not limited to the following: grips, seats, and labels.  
3. Repairs performed on Precor equipment missing a serial number or with a serial tag that has  
been altered or defaced.  
4. Service calls to correct installation of the equipment or instruct owners on how to use the  
equipment.  
5. Pickup, delivery, or freight charges involved with repairs.  
6. Any labor costs incurred beyond the applicable labor warranty period.  
Warranty Periods and Coverage  
All residential products and commercial products used in the home are warranted for the  
following periods:  
Disclaimer and Release  
The warranties provided herein are the exclusive warranties given by Precor and supersede any prior,  
contrary or additional representations, whether oral or written. ANY IMPLIED WARRANTIES, INCLUDING THE  
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE THAT APPLY TO ANY PARTS DESCRIBED ABOVE  
ARE LIMITED IN DURATIONTO THE PERIODS OF EXPRESS WARRANTIES GIVEN ABOVE FOR THOSE SAME PARTS.PRECOR  
HEREBY DISCLAIMS AND EXCLUDESTHOSE WARRANTIES THEREAFTER. Some states do not allow limitation on how  
long an implied warranty lasts, so the above limitation may not apply to you. PRECOR ALSO HEREBY DISCLAIMS  
AND EXCLUDES ALL OTHER OBLIGATIONS OR LIABILITIES, EXPRESS OR IMPLIED, ARISING BY LAW OR OTHERWISE, WITH  
RESPECT TO ANY NONCONFORMANCE OR DEFECT IN ANY PRODUCT, INCLUDING BUT NOT LIMITED TO: (A) ANY OBLIGATION,  
LIABILITY, RIGHT, CLAIM OR REMEDY IN TORT, WHETHER OR NOT ARISING FROM THE NEGLIGENCE OF PRECOR OR ITS  
SUPPLIERS (WHETHER ACTIVE, PASSIVE OR IMPUTED);AND (B) ANY OBLIGATION, LIABILITY, RIGHT, CLAIM, OR REMEDY FOR  
LOSS OF OR DAMAGE TO ANY EQUIPMENT. This disclaimer and release shall apply even if the express warranty set  
forth above fails of its essential purpose.  
Lifetime frame and welds  
10 years parts and wear items  
1 year labor  
Coverage for options and accessories defined below.  
Options / Accessories  
Many options or accessories have components that are connected internally or mounted inside the  
electronic console.The following guidelines determine the warranty for these components. If the  
internal components are installed by the factory or by an authorized dealer as part of the original  
sale and delivery, they have a warranty that is identical to the warranty of the equipment in which  
they are connected or mounted. If the internal components are not installed by the factory or by an  
authorized dealer as part of the original sale and delivery, they have a 90-day parts and labor  
limited warranty. All components that are not internally connected have 90-day parts only limited  
warranty. Satisfactory proof of purchase is required in all cases.  
Exclusive Remedies  
For any product described above that fails to conform to its warranty, Precor will provide, at their option, one of  
the following: (1) repair; (2) replacement; or (3) refund of the purchase price. Precor Limited Warranty service  
may be obtained by contacting the authorized dealer from whom you purchased the item. Precor  
compensates Servicers for warranty trips within their normal service area to repair equipment at the owner’s  
location. You may be charged a trip charge outside the service area. THESE SHALL BE THE SOLE AND EXCLUSIVE  
REMEDIES OFTHE BUYER FOR ANY BREACH OFWARRANTY.  
Conditions and Restrictions  
This warranty is valid only in accordance with the conditions set forth below:  
1. The warranty applies to the Precor product only while:  
a. It remains in the possession of the original purchaser and proof of purchase is  
demonstrated  
Exclusion of Consequential and Incidental Damages  
b. It has not been subjected to accident, misuse, abuse, improper service, or non-Precor  
modifications  
c. Claims are made within the warranty period  
PRECOR AND/OR ITS SUPPLIERS SHALL HAVE NO OBLIGATION OR LIABILITY, WHETHER ARISING IN CONTRACT  
(INCLUDING WARRANTY), TORT (INCLUDING ACTIVE, PASSIVE, OR IMPUTED NEGLIGENCE AND STRICT LIABILITY), OR  
OTHERWISE, FOR DAMAGE TO THE EQUIPMENT, PROPERTY DAMAGE, LOSS OF USE, REVENUE OR PROFIT, COST OF  
CAPITAL, COST OF SUBSTITUTE EQUIPMENT, ADDITIONAL COST INCURRED BY BUYER (BY WAY OF CORRECTION OR  
OTHERWISE) OR ANY OTHER INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, WHETHER  
RESULTING FROM NONDELIVERY OR FROM THE USE, MISUSE OR INABILITY TO USE THE PRODUCT. This exclusion  
applies even if the above warranty fails of its essential purpose and regardless of whether such damages  
are sought for breach of warranty, breach of contract, negligence, or strict liability in tort or under any other  
legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages,  
so the above limitation might not apply.  
2. This warranty does not cover damage or equipment failure caused by electrical wiring not in  
compliance with electrical codes or Precor owner’s manual specifications, or failure to provide  
reasonable and necessary maintenance as outlined in the owner’s manual.  
Complete this portion and keep for your records.  
Purchased From: ____________________________ Example: Dealer or store name.  
Phone Number: _____________________________ Example: Dealer or store telephone number.  
Product/model: _____________________________ Example: M9.31  
This warranty gives you specific legal rights, and you may also have other rights, which vary state  
to state.  
Effective 01 January 2003  
Serial number:______________________________ The serial number is found on the shipping container  
P/N 36287-110  
page 11  
 
 
 
Please detach and mail in the warranty registration within ten days of purchase.  
 
 
S3.15 Multi-Hip Option Specifications  
Length: 32 inches (81 cm)  
Height: 46 inches (115 cm)  
Width: 30 inches (75 cm)  
Shipping weight: 51 lb (23 kg)  
Precor Incorporated  
20031 142nd Avenue NE  
P.O. Box 7202  
Woodinville, WA USA 98072-4002  
Precor is a registered trademark of Precor Incorporated.  
Specifications subject to change without notice.  
Copyright 2006 Precor Incorporated.  
S3.15 Multi-Hip Option Literature Kit 49452-101  
S3.15 Multi-Hip Option Assembly Instructions 49453-101  
Warranty Registration 45623-102  
NOTICE:  
Precor is widely recognized for its innovative, award winning designs of exercise equipment. Precor aggressively seeks U.S. and foreign patents for  
both the mechanical construction and the visual aspects of its product design. Any party contemplating the use of Precor’s product designs is hereby  
forewarned that Precor considers the unauthorized appropriation of its proprietary rights to be a very serious matter. Precor will vigorously pursue all  
unauthorized appropriation of its proprietary rights.  
Warranty Card # 36287-110  
15 September 2006  
 

Pelco Projection Television C2928M QS User Manual
Phase Technology Speaker RS800i User Manual
Philips Battery Charger SCE4430 12 User Manual
Philips DVD Player BDP2700 User Manual
Philips Electric Shaver 7240XL User Manual
Philips Headphones SBCHS550 User Manual
Pioneer Car Stereo System DEH 4400HD User Manual
Poulan Lawn Mower 176085 User Manual
Poulan Lawn Mower XT19H42YT User Manual
Procom Stove QL300RYLA User Manual